CONCRESEAL® TH-S is a waterproof polymer-modified cement-based mortar for priming insulation panels of polyurethane foam or polystyrene. Once applied, it provides a high bond strength on the surface for the finish with façade mortars or acrylic coatings.

Waterproof coloured cement based mortar with good adhesion, for the protection and decoration of façades. available in three different types depending on the final finish.

CONCRESEAL® TOP-AC is a high-quality acrylic coating with selected aggregate specially designed for waterproofing and finish of facades composed of polystyrene and polyurethane panels. Once applied, it provides a layer with decorative rough finish over properly prepared insulation panels.

CONCRESEAL® TOP-S is a cement-based mortar specially designed for waterproofing and decoration of facades composed of polystyrene and polyurethane panels. Once applied, it provides a layer with decorative rough finish over properly prepared insulation panels.

MAXCLEAR® is a high-quality siloxanebased water-repellent (hydrophobic impregnation) for the transparent protection against rainwater and weathering of concrete, façade mortar, brick, and stone. It is supplied as a solvent-based liquid ready to use by brush or low-pressure spray application.

MAXCLEAR®-D is a water-repellent liquid composed of invisible water-based silicon resin specially formulated for limestone substrates or similar, low-fired clay and gypsum plasters. It is supplied ready to use and it can be applied by brush or low-pressure spray.

Milky liquid that once applied on a substrate, protects it against painting of graffiti aiding in their later elimination.

High concentration and surfactant cleaner gel, formulated for the elimination of paint and graffiti.

MAXCLEAR® SULFAT is a one-component water-based liquid product. Once applied it penetrates by difussion and capillarity into the substrate to provide a barrier against salts and avoiding the appearance of efflorescences on the surface. It is readyto- use on absorbent mineral substrates such as concrete, cement-based mortar and bricks.

MAXCLEAR® TOP is a high-quality, hydrophobic sealer composed of water-based silane/ siloxane resins, specifically designed as transparent waterrepellent and protection against rainwater and weathering on concrete, brick, cement mortar, masonry, natural stone and limestone substrates. It is supplied in liquid form ready to be applied directly by brush, roller or sprayed at low pressure.

MAXEPOX® REPAIR is a solvent-free, three-component, epoxy-based mortar, specially designed for levelling, protection and concrete repair on horizontal surfaces up to 50 mm thickness per layer. Repaired areas provide a high performance surface with excellent mechanical and impact resistance, as well as high abrasion and chemical resistance.

MAXFLOOR® is a coloured and two-component water-based epoxy coating suitable for protective and decorative coating of floors and surfaces in general. It is available in two different versions:
- MAXFLOOR® MATT for an eggshell, matt finish.
- MAXFLOOR® GLOSS for a smooth glossy finish.

MAXGLAZE®-D is a transparent polymer sealer, derived from methacrylate-based resins. It forms a durable, tough and flexible film with gloss finish for protection of concrete and masonry. It resists weathering, air pollutants, alkaline agents and ultra-violet rays.

MAXMORTER® CAL is a mortar based on lime and inert aggregates with controlled size. It is specially designed for repair, pointing of joints and rendering of deteriorated stone and brick elements in masonry, for both interior and exterior applications.

MAXMORTER® CAL-F is a lime-based mortar composed of calcium hydroxide, fine grain sized aggregates and special admixtures. It is specially designed to be applied on previous renders in order to provide a thin coat (1-3 mm) with smooth finish, suitable for indoor and outdoor applications.

MAXQUICK® ROLL is a polymer modified mortar, supplied in powder form. Once mixed with water, produces a decorative coating that is easily placed in a single layer with good waterproofing performance.

MAXREPAIR® INJECTION is a one-component and shrinkage-compensated mortar, formulated from cement, mineral aggregates and modified with polymers which provides high adhesion, medium-resistance and excellent fluidity. Contains no chlorides or metallic particles. It comes in powder form, ready to use mixing only with water.

MAXSHEEN® ELASTIC is a water-based pure acrylic product which provides an elastic, durable and high performance coating suitable for waterproofing, anti-carbonation protection and decoration of concrete structures and masonry in all kind of civil engineering works and buildings. It is available in two versions: smooth and textured finish.

MAXURETHANE® TOP is a one-component coating based on flexible, transparent, air-cured synthetic aliphatic polyurethane resins. Once cured, it provides a protective coating with glossy or matt finish and high resistance against weathering for protection of concrete and masonry surfaces.
In case a colour finish is needed, MAXURETHANE® TOP can be mixed with the pigment paste MAXURETHANE® DECOR (Technical Bulletin no. 58). Meets the requirements of European Standard EN 1504-2; Surface protection systems for concrete.

THERMOSAN® CAL is a one-component, macroporous mortar based on hydraulic lime and light weight aggregates with polypropylene fibres and thermal-dehumidifying properties, which forms a layer for restoration and treatment of substrates damaged by capillary rising dampness.