BISEAL® AF is an anti-freeze admixture for concrete and mortars, with no chlorides or fluorides.

BISEAL® CEL is an air-entraining admixture to make low density cellular concrete. It increases highly the air content in concrete, with small air cells uniformly distributed throughout the concrete matrix.

BISEAL® FIBER are 100% virgin-polypropylene fibers without reprocessed olefin materials and produced in according to specifications ASTM C 1116 TYPE III GMP. These fibers are suitable for adding to concrete and mortars and have been specially studied for concrete industry. When fibers have been distributed homogeneously in the mixture, provide a reinforcement three-dimensional structure, which improves mechanical properties such as impact resistance, and also lead a long lasting for concrete and allow to control and minimize the cracking due to shrinkage. Three different versions are available according to the fiber length: 6, 12 and 18 mm.

BISEAL® FIBER -MF is a polyolefin macro-fiber designed specifically for reinforcement of concrete. It is added directly on concrete mixing, being distributed uniformly and increases the mechanical and ductility properties of the concrete, allowing even the load-carrying after cracking.

BISEAL® FS is a chloride-free accelerating liquid admixture for concrete and mortars.

APPLICATION FIELDS

Preparation of concrete, with or without reinforcement, and mortars which require fast setting in:
• Concrete placing under water, avoiding wash out of concrete.
• Manufacturing pre-cast elements for fast mould removal.

BISEAL® FUME is a powder admixture, based on densified silica fume, which is added in order to provide cohesion and reduce bleeding of fresh concrete and mortar mixes, and to increase highly its mechanical strength once hardened.

BISEAL® MEV are free-silica, chemically neutral, silicon-sodium-calcium solid glass microspheres suitable for dusting on a fresh coating or mixing with a transparent binders, such as resins of MAXEPOX® or MAXURETHANE® range, to provide anti-slip and safety flooring system.

BISEAL® MRL is a water-based emulsified oil, specifically designed for the de-moulding of concrete on all kind of formwork surfaces, with or without absorption, such as metal, plastic, wood, gypsum, etc.

BISEAL® PL is a concentrated plasticiser admixture to improve workability of fresh concrete and mortar, and to reduce mixing water. Its air-entraining side effect improves frost resistance and water absorption for concrete and mortars.

BISEAL® POL is a liquid admixture, that is added to the mixing water for concrete or mortar, and depending on the dosage, acts as a plasticiser, superplasticiser or high range water reducer, providing a highly fluid concrete and improved mechanical resistance.

Liquid for delaying the setting of concrete. Allows preparation of exposed aggregate concrete.

Liquid for delaying the setting of concrete. Allows preparation of exposed aggregate concrete.

BISEAL® SCC is a superplasticiser liquid admixture based on a modified polycarboxilic polymer, designed especially for obtaining Self Compacting Concrete (SCC) and High Performance Concrete (HPC). BISEAL® SCC can produce very high workable concrete, with cohesion and no risk of segregation or bleeding, placed and compacted under its own weight with minimal vibration required.

BISEAL® SPF is a liquid admixture, which once added to the mixing water of concrete and mortar, and depending on the dosage, acts as a superplasticiser or high range reducer of mixing water, providing high fluidity and improved mechanical resistance of concrete and mortars.

BISEAL® SRA is a liquid admixture that once added to the mixing water reduces the plastic and drying shrinkage of concrete and mortar, reducing the risk of cracking during the curing process.

BISEAL® WA is a chloride-free liquid waterproofing admixture that reduces the permeability and water absortion of mortars and concrete, providing high waterproofing properties.

CONCRESEAL® CARBOFIX is a low-modulus cement-based mortar, specifically designed to be used as part of a system for fixing carbon fiber mesh DRIZORO® CARBOMESH on all types of substrates in repair and strengthening works.

DRIZORO® SILICA is a well-graded, clean, dry siliceous aggregate with controlled granulometry, free of salts and pollution, specially designed for use in the mixing of micro-concretes and mortars, non-slip coatings, and multi-layer flooring systems.

DRIZORO® SILICA DECOR is a well-graded dry siliceous sharp sand with controlled granulometry from 1,0 to 2,0 mm, free of salts and pollution, specially designed to provide a decorative finish, mixed with transparent epoxy/ polyurethane resins or with cement-based mortars.

It is available in five different colours to produce a wide variety of finishes.

DRIZORO® VEIL is an alkali-resistant glass fibre veil (G-45/M-100) or polyester fibre veil (E-45/E-60/E-100), especially designed for the reinforcement of resin-based coatings in order to increase its tensile strength and crack-bridging capability.

MAXBETON® is a hydraulic, quick setting, non-shrink mortar for placing and fixing of elements in building and civil works. Its thixotropy allows the placing in both vertical and horizontal surfaces as well as overhead areas.

MAXBOND® is a one-component quid based on acrylic resins, specially formulated to improve the bonding between different layers of concrete. For mortars, it provides greater adhesion on smooth and porous-free surfaces or on the contrary very absorbent substrates. It acts as a bonding agent between the two elements to joining.

MAXBOND® LATEX is a water-based styrene-acrylic liquid admixture for mixing of bonding slurries and improvement of physical properties for mortars and concretes. Mixes prepared with MAXBOND® LATEX have a greater adhesion, workability, cohesion, and retention of the mixing water.

Once hardened, MAXBOND® LATEX improves abrasion and wearing resistance and reduces water absorption by capillarity.

MAXBOND ® -S is a one-component product liquid based on acrylic resins that has been specially formulated to improve the bonding between different layers of concrete and mortar, providing a higher adhesion on smooth and porous-free surfaces or on the contrary, very absorbent substrates.

MAXCLEAN® is an acidic pH liquid cleaner specially designed to remove salts, greases and oils on concrete or cement surfaces. Its special formulation, attacks, and dissolves stains, facilitating their removal

MAXCLEAN ® -D is a water-based cleaning agent, specially designed to remove stains of oils, greases and waxes on concrete, mortars and other building elements.

MAXCLEAN® ECOGEL is an ecologic and biodegradable paint remover with gel consistency, formulated to eliminate acrylic paints and graffities.

MAXCLEAN® -N is a cleaning gel with neutral pH specially formulated for removal of pollution stains and general dirt from all kinds of natural stone (granite, marble, slate, limestone, sandstone, etc.), artificial stone, brick, ceramic tile, glazed tiles, pre-cast block, concrete and cement mortars.
Its special non-corrosive and non-hazardous formulation with no solvents or other aggressive chemicals, allows an effective cleaning without harmful effects to the environment and with no changes to the colour, appearance, and texture of the substrate.

MAXCLEAN ® – R is a high concentrated paint removal gel, surfactant, formulated to eliminate synthetic paints as a powerful coating stripper.

High concentration and surfactant cleaner gel, formulated for the elimination of paint and graffiti.

MAXCRYL® is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties of cement-based mortars and concrete. The fresh mixes prepared with MAXCRYL®, provide greater adhesion, workability, cohesion and water retention. Once hardened, MAXCRYL® improves the mechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction of water absorption by capillarity.

MAXCURE® is a water-based milky pure acrylic resin, that sprayed over the surface of fresh concrete or mortar, provides a thin film acting as a protective barrier to prevent an excessive fast drying.

MAXDUR® -C is a product formulated with special cements, silica and corundum of high hardness, together with pigments, additives and aggregates designed to be applied on fresh concrete in order to improve its abrasion resistance and provide an anti-dust finish in one single application.

MAXELASTIC® PUR CAT is an accelerator catalyst specially designed to be used with the polyurethane elastic membrane MAXELASTIC® PUR in order to speed up the drying and curing time of the applied coating.

MAXELASTIC ® PUR PRIMER is a twocomponent, solvent-free, low viscosity, transparent epoxy primer to be used prior to application of the MAXELASTIC ® PUR waterproofing liquid membrane, acting as an excellent bonding agent and a vapour barrier.

MAXEPOX® AC is a two-component, water-based epoxy primer with non-toxic corrosion inhibitors, and specially designed to provide a high performance protective coating for metal surfaces against any corrosion process.

MAXEPOX ® BOND is a two-component and 100% solids –solvent free- epoxy-based bonding agent, which has been specially designed for the bonding of construction materials.

MAXEPOX® BOND-G is a two-component and 100% solids –solvent free- epoxy-based bonding agent, which has been specially designed for the bonding of metal plates over concrete or between different construction elements.

MAXEPOX® BOND -S is a two-component and 100% solids –solvent free- epoxy-based bonding agent, which has been specially designed for the bonding of construction materials and the application with spraying methods.

MAXEPOX® BOND-W is a two-component, 100% solids –solvent free-, epoxy-based bonding agent, which has been specially designed for the bonding of construction materials when the humidity in the substrate is high.

MAXEPOX® CAT is a solvent-free catalyst specially designed to be used with solvent-free epoxy resins in order to speed up the drying and curing time of coatings and flooring systems.

MAXEPOX® PRIMER is a two-component, transparent, solvent-free epoxy primer, which has been specially designed to ensure and enhance the adhesion for epoxy flooring systems.

MAXEPOX® PRIMER-W is a two-component, water-based epoxy formulation, designed as primer for polyurethane, polyurea and epoxy coatings to be applied on concrete, mortar, metal substrates, etc in execution of waterproofing and flooring jobs.

MAXEPOX® SOLVENT is a special mixture of organic solvents and thinner suitable for applications of DRIZORO® products formulated with epoxy-based resins.

MAXEPOX® THIX is a low density polyethylene fiber designed to be added on epoxy and polyurethane resins to increase its viscosity and to reduce slump on slopes, vertical surfaces and critical points.

MAXEPOX® THIX-V is an additive in powder form and quick dispersion, suitable as thickener and/or thixotropic additive for epoxy and polyurethane systems

MAXFLEX® 100 HM is an one-component, polyurethane-based, elastomeric sealant and adhesive. It cures at ambient temperature under the influence of the atmospheric humidity, providing a bonding with high elasticity modulus.

MAXFLEX® 100 LM is an one-component, polyurethane-based, elastomeric sealant. It cures at ambient temperature under the influence of the atmospheric humidity, providing a joint sealant with low elasticity modulus.

MAXFLOOR® FILLER is a mixture of well-graded, clean, dry siliceous aggregate and quartz powder free of salts and pollution, specially designed for use in the mixing of fluid/self-levelling resin-based mortars, non-slip coatings, and multi-layer flooring systems.

MAXFLOOR® MARINE is a two-component mortar composed of component A, water-based acrylic resin, and component B, cement-based mortar with special additives. Once mixed, it provides a non-slip mortar with high flexibility and adhesion, suitable for protection against corrosion and abrasion on metal surfaces.

MAXPATCH® DECOR is a water-based, UV-stable, liquid pigment paste for colouring cement-based mortars at job-site.

MAXPATCH® EXTRAFINO is a cement-based mortar with selected aggregates and special additives. Once mixed with its resin MAXPATCH® LIQUID, provides a mortar of high mechanical performance (adhesion, abrasion resistance and compression) and suitable for cosmetic/decorative finish of continuous pavements from 1 to 2 mm thickness, on previously levelled surfaces with MAXPATCH® or MAXPATCH® FINO.

MAXPRIMER® is a two-component, transparent, solvent-based epoxy primer, which has been specially designed to ensure and enhance the adhesion for epoxy flooring systems on concrete.

MAXPRIMER® FLOOR is a one-component liquid composed of water-based acrylic resins, to be applied by brush, roller or air-less spray equipment. It is specially designed to be used as a bonding agent to improve adhesion of cementbased mortars on concrete floors, as well as a sealing primer to reduce substrate porosity and appearance of air bubbles on surface.

MAXPRIMER® PUR is a one-component transparent primer composed of solvent-based silanes, that once applied reacts and acts as a chemical bonding, building binder bridges between substrate and polyurethane-based coatings.

It is designed to improve the adhesion of polyurethane coatings on both low or non-porous substrates such as vitrified elements, gresite, ceramic tile, glass, terrazzo, marble, granite, metal (aluminium, cupper, steel ), rigid plastic and polished concrete.

MAXPRIMER® PUR -W is a water-based, two- component, transparent primer composed of aliphatic polyurethane resins, that once applied has excellent adhesion on porous and non-porous surfaces, such as ceramic tiles, vitrified or glazed elements, mosaic, glass, terrazzo, marble, granite, metal, rigid plastic, concrete, etc.

MAXURETHANE ® 2C SOLVENT is a special mixture of organic solvents suitable for mixing and cleaning of MAXURETHANE® 2C.

MAXURETHANE® INJECTION CLEANER is a special agent for flushing and cleaning of DRIZORO® injection resins formulated with water-reactive polyurethane-based resins.

MAXURETHANE® CEM PRIMER is a two-component, solvent-free, polyurethane-cement based primer, which has been specially designed to seal suface porosity and ensure the adhesion of polyurethane coatings on concrete and porous substrates.